Search results for "020501 mining & metallurgy"
showing 10 items of 14 documents
Effect of active heating and cooling on microstructure and mechanical properties of friction stir–welded dissimilar aluminium alloy and titanium butt…
2019
A butt joint configuration of AA6061–pure Ti was welded using friction stir welding (FSW) with an assisted cooling and heating conditions, aiming to attain a flawless joint. Cooling-assisted friction stir welding (CFSW) was carried out with a different cooling medium such as CO2, compressed air and water at controlled flow rate. However, heating-assisted friction stir welding (HFSW) was performed with heating source of GTAW torch just before FSW tool at different current density. Prepared specimens were subjected to optical microscopy (OM), scanning electron microscopy (SEM) and electrodischarge spectroscopy (EDS) for microstructural characterizations. The tensile strength and microhardness…
Flotation with sedimentation: Steady states and numerical simulation of transient operation
2020
Abstract A spatially one-dimensional model of the hydrodynamics of a flotation column is based on one continuous phase, the fluid, and two disperse phases: the aggregates, that is, bubbles with attached hydrophobic valuable particles, and the solid particles that form the gangue. A common feed inlet for slurry mixture and gas is considered and the bubbles are assumed to be fully aggregated with hydrophobic particles as they enter the column. The conservation law of the three phases yields a model expressed as a system of partial differential equations where the nonlinear constitutive flux functions come from the drift-flux and solids-flux theories. In addition, the total flux functions are …
Experimental investigation of low-frequency pulsed Lorentz force influence on the motion of Galinstan melt
2016
Abstract The paper presents the results of the numerical and physical experiments, aimed at assessing the influence of pulsed force of electromagnetic field on the melt motion and the fluid velocities. The experiment was performed on the eutectic alloy Galinstan in the cylindrical volume, where an ultrasonic Doppler velocimeter was employed for velocity measurements under conditions of pulsed and steady EM field application. A numerical simulation of the melt flow, forced by the steady EM force, involved a 2D axisymmetric model. The k-e turbulence model was used to obtain the information about the melt velocities. The verification of the numerical model was carried out for the steady case. …
Mechanical properties and microstructural study of homogeneous and heterogeneous laser welds in α, β,and α + β titanium alloys
2018
International audience; Heterogeneous welding has been investigated for three different couples of titanium alloys: α/α + β, α/β,andα + β/β. Plates of 100 × 60 mm and 1.6 or 1.8 mm thick were welded with a Yb:YAG laser. Tensile tests show that the resistance of the heterogeneous welded specimens was generally controlled by those of the weakest material except for the α + β/β where the ultimate tensile strength was approximately equal to the average value of both materials. In every case, the elongation of the welded sample was found to be smaller than that of the base metals. The rupture generally took place outside the weld metal and was found to be most of the time located in the alloy ha…
Gas bubbles and liquid metal flow influenced by uniform external magnetic field
2017
Permanent magnet centrifugal pump for liquid aluminium stirring
2016
In liquid aluminium processing, it is important to ensure continuous mixing of the molten metal to ensure temperature and composition homogeneity, and to improve degassing of the metal. Aluminium and its alloys are often processed in special degassing chambers after preparation in order to avoid segregation and to improve material structure, and to avoid gas pores. This extra step increases material costs and may cause material contamination. In this article, we present the idea to use centrifugal permanent magnet stirrer to induce liquid aluminium motion through thick furnace wall by creating high-speed local liquid metal jet. Analytical estimation, numerical modelling and experimental tes…
Permanent magnet dipole stirrer for aluminium furnaces
2018
Use of permanent magnet systems for metallurgical applications have been proposed before. We have continued development of such systems by investigation use of single magnetic dipole which is realized as permanent magnet cylinder. Magnet is magnetized orthogonal to its axis and has been mounted to the side of the liquid metal reservoir. System first was modelled using small scale experiment with galinstan melt. Velocity distributions and flow patterns in reservoir using Ultrasound Doppler Anemometer were acquired and will be presented here. Additionally, numerical model using Comsol and Cenos modelling software were developed alongside analytical, non-dimensional estimation calculations. Ex…
Numerical and experimental study of liquid metal stirring by rotating permanent magnets
2018
In this work, we study liquid gallium stirring by rotating permanent magnets. We demonstrate possibility of easily creating different flow patterns by rotating permanent magnets, which can be industrially important for controlling heat and mass transfer processes in the system. Unlike the typical approach of simulating magnet rotation as a transient problem and time-averaging the Lorentz forces, we solve the magnet rotation as a harmonic (frequency domain) problem, which leads to forces equal to time-averaged ones and decreases the simulation time considerably. Numerical results are validated using qualitative flow structure results from the neutron radiography visualization of tracer parti…